December 23, 2024, 09:50:26 PM
Forum Rules: Read This Before Posting


Topic: What is making process of White Zinc Sulphide  (Read 8315 times)

0 Members and 1 Guest are viewing this topic.

Offline ach

  • Very New Member
  • *
  • Posts: 1
  • Mole Snacks: +0/-0
What is making process of White Zinc Sulphide
« on: December 20, 2007, 06:58:28 AM »
What is making process of White Zinc Sulphide in Bulk qunatity.
Could u give me methos of making step by step.

Ach

Offline AWK

  • Retired Staff
  • Sr. Member
  • *
  • Posts: 7976
  • Mole Snacks: +555/-93
  • Gender: Male
Re: What is making process of White Zinc Sulphide
« Reply #1 on: December 20, 2007, 07:59:59 AM »
The method is extremely simple. You should just mix two solution: any soluble salt of zinc and sodium sulfide in proper stoichiometry.
« Last Edit: December 20, 2007, 08:53:41 AM by AWK »
AWK

Offline Alpha-Omega

  • Full Member
  • ****
  • Posts: 693
  • Mole Snacks: +360/-231
  • Gender: Female
  • Physical Inorganic Chemist
Re: What is making process of White Zinc Sulphide
« Reply #2 on: December 31, 2007, 04:28:56 PM »
Usually with the direct reaction of zinc and sulfur as a powder and then heated.  The reaction is highly exothermic and has been used as rocket fuel in the past, and the reaction should be performed under an explosives hood and in small quantities at a time (not more that a gram).

Additionally, avoid any contact with water or aqueous inorganic acids since the evolution of hydrogen sulfide gas is imminent; and, it is toxic and unpleasant.

Oh, and while it is  hot make sure it doesn't oxidize in air and give zinc oxide and SO2.

Offline AWK

  • Retired Staff
  • Sr. Member
  • *
  • Posts: 7976
  • Mole Snacks: +555/-93
  • Gender: Male
Re: What is making process of White Zinc Sulphide
« Reply #3 on: January 02, 2008, 01:15:28 AM »
Method of Alpha-Omega will not give pure ZnS
« Last Edit: January 16, 2012, 02:31:23 PM by Arkcon »
AWK

Offline Alpha-Omega

  • Full Member
  • ****
  • Posts: 693
  • Mole Snacks: +360/-231
  • Gender: Female
  • Physical Inorganic Chemist
Re: What is making process of White Zinc Sulphide
« Reply #4 on: January 02, 2008, 01:38:58 AM »
There is more than one way to synthesize a compound...this would be semi-conducting

grade....http://en.wikipedia.org/wiki/Zinc_sulfide

you will have to search for the process that will make the grade you desire....it will synthesize from yellow to white....depending on what you like....if you get a mixture of grades....you will have to use a post treatment to clean it up...

Offline Alpha-Omega

  • Full Member
  • ****
  • Posts: 693
  • Mole Snacks: +360/-231
  • Gender: Female
  • Physical Inorganic Chemist
Re: What is making process of White Zinc Sulphide
« Reply #5 on: January 02, 2008, 02:18:19 AM »
Never let it e said I am not thorough.  Here is what happens with this recipe and indeed there is a competing rxn:

A mixture of zinc and sulfur reacts spontaneously, under a flash of fire and smoke. The gray-green mixture is transformed into an off-white powder with magical properties.
Ingredients: fine powdered zinc, fine powdered sulfur

Procedure: A minimal recipe follows.

1. Measure out zinc and sulfur in a 1:1 molar ratio. A rough approximation might be 6.5 g of zinc and 3.2 g of sulfur.

2. Mix the zinc and sulfur powders together thoroughly.

3. Ignite the mixture using a "white hot" metal loop.

Understanding: The zinc and sulfur react violently, producing a substantial quantity of heat, light, and smoke. The principle reaction is between zinc and sulfur

Zn(s) + S(s) → ZnS(s)

However, when the reaction is run under aerobic conditions in air, there is a competing reaction
2 Zn(s) + O2(g) → 2 ZnO(s)

 The reaction forms an off-white crystalline powder of zinc sulfide. For many years, zinc sulfide has been known to be phosphorescent. It is often used a phosphor, for example, in paints used on watch dials. As a mineral, it is found as "sphalerite."

The reaction of an excess of zinc may lead to formation of zinc oxide, commonly known as "zinc white." Zinc white is a common pigment found in paints. It is also a principal component of ointments designed to prevent sunburn in the summer, windburn in the winter, and diaper rash ... all year around! In nature, zinc oxide is found as the mineral "zincite."

AND BECAUSE I SO LOVE XRF:


In fluorescence, light energy is absorbed and then rapidly reemitted. In phosphorescence, the light energy is absorbed but then reemitted over a longer period of time. It is the "delay" in the emission of phosphorescence that distinguishes it from fluorescence.

During exposure to short wavelength (254 nm) UV light, the product of our reaction is observed to fluoresce. The phosphorescent "green" that is seen in the image is the zinc sulfide product.

During exposure to long wavelength (366 nm) UV light, the zinc sulfide is found to fluoresce and phosphoresce with impressive intensity and vibrant color. After turning the UV light "off" we see the evidence of phosphorescence emission from the zinc sulfide in the form of an "eerie green" glow. The glow is maintain for several seconds.

At the end of the nineteenth century, William Crookes discovered cathode rays. He placed a cathode and anode within a vacuum tube, along with a screen coated with zinc sulfide. Crookes observed a glowing image on the zinc sulfide screen consistent with the hypothesis that "rays" had been emitted by the cathode, causing the zinc sulfide to fluoresce. The ghostly glow that we observed must be much like that observed by Crookes in his discovery of cathode rays more than a century ago.


--------------------------------------------------------------------------------

Sponsored Links